The Altissimo Sit-Stand Workstation from KV Waterloo is an all-in-one solution for converting a sitting desk into a sit-to-stand desk. Mounted at the back, side or corner of the desk, this space-saving workstation effortlessly moves up or down using a gas spring mechanism and is easily stored when not in use. The Single Workstation (6011 Series) accommodates monitors from 5 to 20 lbs, while the Dual Workstation (6021 Series) handles monitors up to 8 lbs each and 24” wide (diagonally).

The height range of the Altissimo is an impressive 22” with the keyboard tray ranging from 5” below desk height to 17” above the desk. The monitor has an additional 9.5” of independent adjustment and can be tilted to 45° or rotated 90° from landscape to portrait orientation. In addition, the monitor tower can rotate independently of the worksurface 180° from left to right.

The keyboard tray is angle adjustable with 14° of negative incline and 4° of positive incline, while also being height adjustable relative to the upper platform. All these adjustable ranges make the Altissimo one of the most versatile sit-stand solutions available. (This model is slightly more versatile than the Altissimo-Plus Sit Stand Workstation, below.)

Note: Those who have already purchased the Single Workstation can upgrade to the Dual model by ordering the Dual Mounting Kit (6021AS60/6021E60). Available colours are Silver (with Gray Accents), Black (with Black Accents), and White (with Gray Accents) (Special Order only).

The Taskmate Go from HealthPostures can retrofit any standard desk to become a sit-stand workstation. The unit uses a robust, well-designed clamping mechanism that can accommodate desks up to 2.0" thick. A single release lever unlocks the counterbalanced spring-assisted mechanism to permit simultaneous adjustement of both the monitor and keyboard. There are 10 available height options all of which are locked upon the release of the adjustment lever (unlike some units which do not have a locking option and can then "drift" downwards when weight is placed on the keyboard tray). The VESA compatible monitor mount can be attached at 6 different height settings, with the distance between the keyboard tray and the middle of the monitor adjustable from a minimum of 6.5" to a maximum of 20".

The Taskmate Go supports up to 35 lbs of weight, and provides a full 17.5" range of vertical movement, meaning the keyboard tray can be positioned from 4" below to 13.5" above the desk surface. The upper platform worksurface is 19.0" x 9.0". There are two keyboard tray options. The Large Tray is a one-piece tray which is 30" x 12". For those wanting a smaller tray with a separate mousing area, the Swing-Out Tray has a 19" x 7.5" area for the keyboard with a separate swing-out mousing area which positions closer to the body and can be reversed for right or left-handed use. An optional (but not recommended) wrist rest is included with the Swing-Out Tray. Either keyboard tray model can be adjusted to a negative tilt of 5 or 10 degrees. The unit ships largely preassembled (apart from the tray) which minimizes setup time.

Le Taskmate Go par HealthPostures transforme (retrofits) tout bureau standard pour devenir un poste de travail d`assis-debout. Ce produit utilise un mécanisme de serrage robuste et bien conçu qui se fixe solidement à n'importe quel bureau jusqu'à 2 po d'épaisseur. La hauteur est ajustable par un seul levier de libération et le mouvement est contrebalancé avec un mécanisme à ressort qui monte et descendre le clavier et le moniteur en même temps. Il y a 12 options de hauteur qui sont toutes verrouillées lorsque le levier d`ajustement est libérer (contrairement à certaines produits qui n'ont pas d'option de verrouillage et peuvent baisser lorsque l'utilisateur s'appuie sur la tablette du clavier). Le moniteur peut être attaché à l'un des 6 points de montage de ce produit, offrant une gamme d`hauteur entre la tablette du clavier et le milieu du moniteur à partir d'un minimum de 8 po et un maximum de 18 po.

Le Taskmate Go peut supporter jusqu'à 35 livres de poids et offre une gamme complète de mouvements de 18 po, ce qui permet de surplomber la tablette du clavier de 2.5 po en dessous du bureau à 13,5 po au-dessus du bureau. La surface de travail de la tablette est 19 po x 9 po et le support du moniteur est compatible avec VESA. La tablette est grande, de 30 po x 12 po. Pour les utilisateurs qui souhaitent une tablette plus petite avec une surface séparée pour la souris, la tablette pivotant a une surface de 19 po x 7,5 po pour le clavier avec une surface pour la souris pivotant séparée. Cela rapproche la souris de l'utilisateur et peut être inversée pour l'utilisation de la main droite ou de la main gauche. Un repose-poignet est inclus avec la tablette Swing-Out Tray. Les deux tablettes de clavier peuvent être ajustés à une inclinaison négative de 10 degrés. Ce produit est expédier assemblé en grande partie (à part de la tablette), ce qui minimise le temps d'installation.

The WorkFit-S clamps onto the front edge of a standard desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray, upper worksurface and monitor through the range of motion. The overall vertical adjustment range is 18", and the monitor mount can be independently adjusted through an additional 4.8" range. The mounting surface must be between .47" and 2.4" thick for the clamp to function, and the monitors must be between 6 and 14 lbs (no greater than 28 lbs total). For optimal viewing comfort monitors can be deployed at a 3° or 8° upward angle. The keyboard tray is 27" wide x 9" deep x 0.25" high, can adjust to a 7.5° negative inclination, and can support a maximum weight of 5 lbs. It can be mounted at 3 different depths which provides a 3" range of adjustment and in addition can also be positioned to either the right or left in order to centrally position the keyboard in front of the monitors. The upper worksurface is 23" wide x 15" deep x 0.25" high, with a maximum load capacity of 5 lbs.

The Dual version is designed to support monitor sizes up to 24.5" physical width and between 6 & 12 lbs. Total combined weight load (including Worksurface, Keyboard and Monitor loads) should not exceed 25 lbs.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S clamps on to the front edge of your desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray, upper worksurface and monitor through the range of motion. The vertical adjustment range is 18", and the monitor mount supports independent vertical adjustment through an additional 4.8" range. The mounting surface must be between .47" and 2.4" thick for the clamp to function, and the monitor must be between 16 and 28 lbs for the LCD pivot (10° down to 20° up) to function correctly. The keyboard tray is 27" wide x 9" deep x 0.25" high, can adjust to a 7.5° negative inclination, and can support a maximum weight of 5 lbs. It can be mounted at 3 different depths which provides a 3" range of adjustment and in addition can also be positioned to either the right or left in order to centrally position the keyboard in front of the monitor. The upper worksurface is 23" wide x 15" deep x 0.25" high, with a maximum load capacity of 5 lbs.

This HD model is designed to accommodate monitor sizes up to 30" and weighing between 16 and 28 lbs can handle a maximum combined weight load (including monitor, worksurface and keyboard loads) of 29 lbs.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S clamps on to the front edge of your desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray, upper worksurface and monitor through the range of motion. The overall vertical adjustment range is 18", and the monitor mount can be independently adjusted through an additional 4.8" range. The mounting surface must be between .47" and 2.4" thick for the clamp to function, and the monitor must be between 6 and 16 lbs for the LCD pivot (10° down to 20° up) to function correctly. The keyboard tray is 27" wide x 9" deep x 0.25" high, can adjust to a 7.5° negative inclination, and can support a maximum weight of 5 lbs. It can be mounted at 3 different depths which provides a 3" range of adjustment and in addition can also be positioned to either the right or left in order to centrally position the keyboard in front of the monitor. The upper worksurface is 23" wide x 15" deep x 0.25" high, with a maximum load capacity of 5 lbs.

The LD version is designed to support monitor sizes up to 24" diagonal and between 6 and 16 lbs. Total combined weight load (including Worksurface, Keyboard and Monitor loads) should not exceed 18 lbs. For monitor sizes larger than 24" diagonal or total weight loads greater than 18 lbs. the HD version of this product may be an option.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S clamps on to the front edge of your desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray and monitor through the range of motion. The vertical adjustment range is 18", and the monitor mount independently can vertically adjust an additional 5". The desk edge must be between .47" and 2.4" thick for the clamp to function, and the monitor must be between 16 and 28 lbs for the LCD pivot to function correctly. The keyboard tray is 16.5" wide x 9.3" deep, and the slide-out mousing surface is 7.5" wide x 7.9" deep, and the maximum weight on the keyboard surface cannot exceed 3 lbs.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S Dual Sit-Stand Workstation clamps on to the front edge of the desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray and monitors through the range of motion. The vertical adjustment range is 18", and the monitor mounts (in tandem) can independently vertically adjust an additional 5". The desk edge must be between .47" and 2.4" thick for the clamp to function, and the monitor must be between 6 and 14 lbs for each monitor for the LCD pivot to function correctly. In addition, the maximum width of each monitor cannot exceed 21.25" (for the LCDs to be able to mount on the Workfit). The keyboard tray is 16.5" wide x 9.3" deep, and the slide-out mousing surface is 7.5" wide x 7.9" deep, and the maximum weight on the keyboard surface cannot exceed 3 lbs.

Note: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S clamps on to the front edge of your desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray and monitor through the range of motion. The vertical adjustment range is 18", and the monitor mount independently can vertically adjust an additional 5". The desk edge must be between .47" and 2.4" thick for the clamp to function, and the monitor must be between 6 and 16 lbs for the LCD pivot to function correctly. The keyboard tray is 16.5" wide x 9.3" deep, and the slide-out mousing surface is 7.5" wide x 7.9" deep, and the maximum weight on the keyboard surface cannot exceed 3 lbs.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.

The WorkFit-S LCD & Laptop Sit-Stand Workstation clamps on to the front edge of your desk and uses the Ergotron's Constant Force spring lift mechanism to assist in moving the keyboard tray and monitor through the range of motion. The vertical adjustment range is 18", and the monitor mount independently can vertically adjust an additional 5". The desk edge must be between .47" and 2.4" thick for the clamp to function, the monitor must be between 6 and 14 lbs and the laptop between 6 and 10 lbs for the unit to function correctly. In addition, the maximum width of the monitor and laptop cannot exceed 21.25". The keyboard tray is 16.5" wide x 9.3" deep, and the slide-out mousing surface is 7.5" wide x 7.9" deep, and the maximum weight on the keyboard surface cannot exceed 3 lbs.

NOTE: It is recommended to strengthen the mounting point to prevent damage to the desktop.