KOCHAB Articulating Keyboard Kit

The KOCHAB Articulating Keyboard Kit by ErgoVerse offers basic keyboard height and tilt adjustability for the budget conscious user. The low cost of the KOCHAB kit makes it an ideal solution for locations where ergonomics are still important but where 1) adjustment will be occasional, 2) full keyboard tray storage is not key, and 3) cost is a factor.

The simple design means that height and angle changes are accomplished simultaneously with a single adjustment. One hand is employed to release or tighten the large, easily locked knob while the other hand moves the keyboard tray to the desired height and angle.

The KOCHAB offers 5.3" of elevation adjustment and 9" of storage travel along a 17" track. A full 360° swivel accommodates situations where alternative mounting (such as lateral) may be needed and heavy-duty steel construction throughout ensures a stable keyboard surface. The 27" wide x 11" deep coated MDF keyboard tray offers sufficient room for the largest of keyboards and a mouse. Some assembly is required.

• Fits Shallow Desks: The 17" track on the KOCHAB Articulating Keyboard Kit is designed to fit desks with limited depth. (Note that this shorter track length will not allow a standard 11" deep keyboard tray mounted on the arm to retract fully beneath the desk; the tray will extend approximately 3" from the front of the desk.) If the tray needs to be stored completely under the desk, this is possible if the track is mounted 3" back from the edge of the desk.
• 5.3" Height Adjustment Range: The KOCHAB Articulating Keyboard Kit offers users 5.3" of height adjustment. The keyboard tray can be positioned level with the underside of the desk and as low as 5.3" below that position. This is sufficient range to accommodate the ergonomic requirements of most users.
• Tilt Adjustable: The angle of the KOCHAB keyboard tray can be adjusted from -10° to +45°. Adjustment is performed simultaneously with height adjustment.
• Single Knob Adjustment: Both tilt angle and height are adjusted simultaneously via a single, easily grasped knob.
• 360° Swivel Joint: The articulating arm is secured to the storage track with a 360° swivel joint. The ability to fully rotate the arm at this joint makes the KOCHAB Articulating Keyboard Kit a versatile option for most commercial single-user or multi-user computer workstations, and a viable solution for improvised computer workstations or those with non-standard dimensions. At the majority of computer desks, with the track installed in its usual perpendicular position, the swivel joint gives users additional usage and storage options along with the noted ergonomic benefits. At a narrow, improvised, or otherwise suboptimal computer station the track can be installed at an angle, or even laterally beneath the desk, and the swivel joint will enable the articulating arm (i.e. the portion on which the keyboard tray will be mounted) to be swiveled forward into the correct ergonomic position for the user. The keyboard tray can still be stored out of the way, even with this atypical installation, by sliding the arm to the back of the track, and then swiveling the keyboard tray to face the rear of the desk.

• KOCHAB Articulating Keyboard Kit Installation Guide: PDF

• Track Length: 17" (42.2 cm)
• Height Adjustment Range: From level with the underside of the desk to 5.3" (13.5 cm) below the underside.
  NOTE: The Kochab tray cannot elevate above the desk surface.
• Tilt Range: -10° to +45°, 17.0" Storage Track
• Tilt & Height Adjustment Mechanism: Single Knob, Simultaneous
• Keyboard Tray Dimensions: 27" (68.6 cm) Wide x 11" (28 cm) Deep
• Warranty: 2 Years
• Package Contents: KOCHAB Articulating Keyboard Kit, Mounting Hardware, Installation Guide
• Tools Required: Phillips Screwdriver, (recommended) Drill and appropriately sized Drill bit to predrill mounting holes.

• Ensure that the KOCHAB will fit the space requirements and provide the movement desired. Remember that the tray will protrude a few inches when recessed as far as possible along the track unless you mount the track 3" back from the edge of the desk. In right angle corner applications it is often advisable to install a Corner Converter to create a straight-edged worksurface which bridges the right angled corner. The KOCHAB can be mounted to the underside of the Corner Converter and the desk, to create a usable worksurface with keyboard tray storage. Mounting to a Corner Converter may require you to drill holes into the converter to match the mounting holes already in the track. Note: When measuring to determine the available mounting space it is important to measure the underside of the desk to ensure you factor in hidden obstacles such as privacy panels, and to ensure nothing will interfere with the mounting of the track or with the tray as it is being stored.
• Optimize the height and angle of the keyboard tray. To adjust the height of the keyboard tray, grasp the front of the tray in one hand and use your other hand to release the locking knob. Move the tray to the desired height and tilt angle and tighten the locking knob to secure it in place.
• Set the tray at the correct height and angle. When setting the height and angle of your keyboard tray make sure you achieve as neutral a posture as possible. Your shoulders should be relaxed (neither hunched nor hanging), your elbows should be at an angle of about 90° or slightly more open, and an imaginary line through the back of your wrists to your forearms should be reasonably straight. Learn More About Correctly Adjusting Your Keyboard Tray
• Use the KOCHAB Articulating Keyboard Kit to bring your mouse and keyboard to you rather than reaching forward for them. Employ the simple height and angle adjustment to position these devices where they can best serve your needs.